E I DUPONT DE NEMOURS INC -- CORIAN PRODUCTS SILICONE SEALANT ALL COLORS  -- 8030-00N073710
<pre>=====================  Product Identification  =====================

Product ID:CORIAN PRODUCTS SILICONE SEALANT ALL COLORS
MSDS Date:09/06/1993
FSC:8030
NIIN:00N073710
MSDS Number: CCPQR
=== Responsible Party ===
Company Name:E I DUPONT DE NEMOURS INC
Address:1007 MARKET ST
City:WILMINGTON
State:DE
ZIP:19898
Country:US
Info Phone Num:800-441-7515
Emergency Phone Num:800-441-3637;800-424-9300(CHEMTREC)
CAGE:0ERJ7
=== Contractor Identification ===
Company Name:E I DUPONT DE NEMOURS & CO, INC.
Address:1007 MARKET STREET
City:WILMINGTON
State:DE
ZIP:19898
Country:US
Phone:800-441-7515
CAGE:0ERJ7
Company Name:E.I. DUPONT DE NEMOURS & CO
Address:1007 MARKET STREET
Box:City:WILMINGTON
State:DE
ZIP:19898
Country:US
Phone:800-441-7515;800-441-9442
CAGE:18873

=============  Composition/Information on Ingredients  =============

Ingred Name:ACETOXY SILANES
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:SILICA GEL; (AMORPHOUS SILICA)
CAS:112945-52-5
RTECS #:VV7310000
OSHA PEL:6 MG/M3
ACGIH TLV:10 MG/M3

Ingred Name:DIMETHYL SILICONE POLYMER
OSHA PEL:N/K 
ACGIH TLV:N/K 

Ingred Name:ACETIC ACID (CERCLA) (DURING CURE, ACETIC ACID IS FORMED
    DURING EXPOSURE TO MOISTURE)
CAS:64-19-7
RTECS #:AF1225000
OSHA PEL:10 PPM
ACGIH TLV:10 PPM;15 STEL
EPA Rpt Qty:5000 LBS
DOT Rpt Qty:5000 LBS

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:NO
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:INHALATION:MAY CAUSE NOSE AND THROAT
    IRRITATION. SKIN CONTACT:REPEATED OR PROLONGED CONTACT MAY CAUSE
    IRRITATION WITH DISCOMFORT AND DERMATITIS. EYE CONTACT:MAY CAUSE
    IRRITATION OR BURNING. INGESTION: NOT A LIKELY ROUTE OF EXPOSURE.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

=======================  First Aid Measures  =======================

First Aid:INHALATION:CONSULT MD IF NECESSARY. SKIN:CLEANSING AFTER USE
    IS ADVISABLE. EYES:IMMEDIATELY FLUSH W/PLENTY OF WATER FOR AT LEAST
    15 MINUTES. CALL MD. INGESTION:CONSULT MD IF NECESSARY.

=====================  Fire Fighting Measures  =====================

Flash Point:>212F,>100C
Extinguishing Media:WATER, DRY CHEMICAL, CO*2.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
    EQUIPMENT . KEEP PERSONNEL REMOVED & UPWIND OF FIRE.
Unusual Fire/Explosion Hazard:NONE SPECIFIED BY MANUFACTURER.

==================  Accidental Release Measures  ==================

Spill Release Procedures:NOTE:REVIEW FIRE FIGHTING MEASURES & HNDLG
    (PERS) SECTIONS BEFORE PROCEEDING W/CLEAN-UP. USE APPROP PERSONAL
    PROT EQUIP DURING CLEAN-UP. VENT SPILL AREA. SOAK UP W/SAWDUST,
    SAND, OIL DRY/OTHER ABSORB	MATL. AQUATIC TOX IS EXPECTED TO BE
    LOW(SUPDAT)
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:AVOID CONTACT W/EYES, SKIN OR
    CLOTHING. KEEP AWAY FROM HEAT, SPARKS & FLAMES. CLOSE CONTAINER
    AFTER EACH USE. STORE BELOW 120F (49C).
Other Precautions:KEEP CONTAINER CLOSED TO PREVENT CONTAMINATION.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:WEAR A NIOSH APPROVED FITTED ORGANIC VAPOR
    RESPIRATOR UNLESS LOCAL EXHAUST VENTILATION IS ADEQUATE OR AIR
    SAMPLING SHOW EXPOSURES ARE W/IN TLV & PEL GUIDELINES. FOLLOW THE
    RESPIRATOR MFR'S DIRECTIONS  FOR RESPIRATOR USE.
Ventilation:PROVIDE SUFFICIENT VENT IN VOL & PATTERN TO KEEP CONTAMS
    BELOW APPLIC OSHA REQUIREMENTS & OTHER SUGGESTED EXPOS LIMITS.
Protective Gloves:RUBBER OR PLASTIC GLOVES.
Eye Protection:ANSI APPROVED CHEM WORKERS GOGGS .
Other Protective Equipment:EYE WASH FOUNTAIN & DELUGE SHOWER WHICH MEET
    ANSI DESIGN CRITERIA .
Work Hygienic Practices:WASH THOROUGHLY AFTER HANDLING. WASH
    CONTAMINATED CLOTHING PRIOR TO REUSE.
Supplemental Safety and Health
SPILL PROC:BASED ON INSOLUBILITY IN WATER.

==================  Physical/Chemical Properties  ==================

Spec Gravity:1.04
Solubility in Water:NIL
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:5

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
NONE REASONABLY FORESEEABLE.
Stability Condition to Avoid:STABLE AT NORMAL TEMPERATURES & STORAGE
    CONDITIONS. DECOMPOSES W/HEAT.
Hazardous Decomposition Products:HAZARDOUS DECOMPOSITION PRODUCTS
    INCLUDE SULFUR OXIDES.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DO NOT FLUSH TO SURFACE WATER OR SANITARY SEWER
    SYSTEM. INCINERATE MATERIAL I/A/W FEDERAL, STATE/PROVINCIAL & LOCAL
    REQUIREMENTS. DO NOT INCINERATE IN CLOSED CONTAINERS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.